Safa, Kamal (2008) Mise au point d'un essai de compaction dynamique. Application au béton. PhD thesis Mécanique, Mécanique, EP/X p.177.

Full text available as: - Thèse_Kamal_Safa_(LMS).pdf ( 10143 Kb )

Licence: Copyright

Abstract

The aim of the thesis is the development of an experimental test of uniaxial compression under static and dynamic loadings, to study the behavior of brittle material and especially concrete. The confinement device is constituted by a tubular steel ring, where the specimen in inserted using a specific protocol. The dynamic axial load is applied by the mean of Hopkinson bars device.

A theoretical part of the work is to optimize the cell dimensions and to develop a reliable method of data utilization that takes into account the various parameters involved in during the test. Still in the theoretical framework but on another subject, the problem of an elastic cylinder submitted on its flat end to a uniform stress over a part of its section, is treated in order to determine the local displacement under the loaded area, called the “elastic punching”. This local displacement results from the difference between the diameter of the cylinder and the one of the loaded area, and intervenes during Hopkinson bars experiments where the diameter of the specimen is usually smaller than the one of the bar. The account of this additional displacement allows for obtaining the correct Young Modulus of the tested material.

The behavior of micro-concrete MB50 was determined in dynamic, static, saturated and dry conditions. Static and dynamic tests conducted on dry and saturated concretes have shed light on several obscure points in the literature, including the influence of water pressure and the strain rate on the behaviour of concrete.

References

[Bailly 1994] P. Bailly, “Une modélisation d’un matériau fragile avec prise en compte d’effets dynamiques”, Compte Rendu Académie des Sciences, Série II, pages 727-732, 1994

[Bazant et al. 1986] Z.P. Bazant, F.C. Bishop, T.P. Chang “Confined compression tests of cement paste and concrete up to 300 Ksi”, ACI Journal, 33: 553-560, 1986

[Benthem et Minderhood 1972] J.P. Benthem and P. Minderhood, “The problem of the solid cylinder compressed between rough rigid stamps”, International Journal of Solid Structures, 8: 1027-1042, 1972

[Bertholf et Karnes 1975] L.D. Bertholf and J. Karnes, “Two-dimensional analysis of the split Hopkinson pressure bar system”, Journal of Mechanics and Physics of Solids, 23: 1-19, 1975

[Biarez 1962] J. Biarez, “ Contribution à l’étude des propriétés mécaniques des sols et des matériaux pulvérilents”, PhD thesis, Université de Grenoble, 1962

[Bishop et Henkel 1957] A.W. Bishop, D.J. Henkel, “The measurement of soil properties in the triaxial test”, Edward Arnold-Publishers-Ltd, 2nd edition, 1957

[Burlion 1997] N. Burlion, “ Compaction des bétons: éléments de modélisation et caractérisation expérimentale”, PhD thesis, ENS Cachan, 1997

[Burlion et al. 2001] N. Burlion, G. Pijaudier-Cabot, N. Dahan, “Experimental analysis of compaction of concrete and mortar”, International Journal for Numerical and Analytical Methods in Geomechanics, 25: 1467-1486, 2001

[Burlion et al. 2005] N. Burlion, F. Bourgeois, J-F Shao, “ Effects of desiccation on mechanical behavior of concrete”, Cement and Concrete Composites, 27: 367-379, 2005

[Buzaud 1998] E. Buzaud, “Performances mécaniques et balistiques du microbéton MB50”, Rapport scientifique final du groupe de recherche formé dans le cadre du réseau de laboratoires « GEO » ; responsable du projet P. Bailly

[Castellote et al. 2004] M. Castellote, C. Alonso, C. Andradea, X. Turtillas, J. Campoc, “Composition and microstructural changes of cement pastes upon heating, as studied by neuron diffraction”, Cement and Concrete Research, 34: 1633-1644, 2004

[Davies 1948] R.M. Davies, “A critical study of the Hopkinson pressure bar”, Philos. Trans. Of the Royal Soc. Of London, A: 240375-240457, 1948

[Eason 1966] G. Eason, “The displacements produced in an elastic half-space by a suddenly applied surface force”, Journal of Applied Mathematics, 2: 299-326, 1966

[Follansbee et Franz 1983] P.S. Follansbee and C. Franz, “Wave propagation in the split Hopkinson pressure bar”, Journal of Eng. and Mater. Techn. 105: 61-66, 1983

[Forquin 2003] P. Forquin, “Endommagement et fissuration de matériaux fragiles sous impact balistique ; rôle de la microstructure”, PhD thesis, ENS Cachan, 2003

[Forquin et al. 2007] P. Forquin, A. Arias, R. Zaera, “An experimental method of measuring the confined compression strength of geomaterials”, International Journal of Solids and Structure, 44: 4291-4317, 2007

[Forquin et al. 2008a] P. Forquin, A. Arias, R. Zaera, “ Role of porosity in controlling the mechanical and impact behaviours of cement-based materials”, International Journal of Impact Engineering, 35: 133-146, 2008

[Forquin et al. 2008b] P. Forquin, G. Gary, F. Gatuingt, “A testing technique for concrete under confinement at high rates of strain”, International Journal of Impact Engineering, 35: 425-446, 2008

[Frazer et al. 1937] R.A. Frazer, W.P. Jones, S.W. Skan, “Approximations to the functions and to the solutions of difference equations”, Aeronautical Research Council R&M 1799, 1937

[Gabet 2006] T. Gabet, “ Comportement triaxial du béton sous fortes contraintes : influence du trajet de chargement”, PhD thesis, Université Joseph Fourier, 2006

[Gama et al. 2004] B. Gama, S. Lopatnikov, J.W. Gillespie, “Hopkinson bar experimental technique: A critical review”, Applied Mechanics Reviews., 57: 223-250, 2004

[Gary et al. 1991] G. Gary, J. Klepaczko, H. Zhao, “Correction de dispersion pour l’analyse des petites deformations auz barres de Hopkinson”, Journal de Physique, Tome III, 1: c3-403, 1991

[Gary et Klepaczko 1992] G. Gary, J. Klepaczko, “Essai de compression dynamique sur béton”, GRECO geomaterial scientific report, pages 105-118, 1992

[Gary et De Greef 2008] G. Gary and V. De Greef, Logiciel de dépouillement DAVID, LMS, 2008

[Gatuingt 1999] F. Gatuingt, “ Prévision de la rupture des ouvrages en béton sollicités en dynamique rapide”, PhD thesis, ENS Cachan, 1999

[Graff 1991] K.F. Graff, “Wave motion in elastic solids”, Dover Publications, New York, 1991

[Grange 2007] S. Grange, “Fragmentation dynamique des roches”, PhD thesis, ENS Cachan, 2007



[Hoek et Franklin 1968] E. Hoek, J.A Franklin, “Simple triaxial cell for field or laboratory testing of rock”, Trans. Inst. Min. Metall., 77: Section A22, 1968

[Hopkinson 1914] B. Hopkinson, “A method of measuring the pressure in the deformation of high explosive by impact of bullets”, Philos. Trans. Of the Royal Soc. Of London, 213: 437-456, 1914

[Horvay et Mirabal 1958] G. Horvay and J.A. Mirabal, “The end problem of cylinders”, Journal of Applied Mechanics, 25: 561-571, 1958

[Jones et Norwood 1967] O.E. Jones and F.R. Norwood, “Axially symmetric cross-sectional strain and stress distributions in suddenly loaded cylindrical elastic bars”, Journal of Applied Mechanics, 34: 718-724, 1976

[Kennedy et Jones 1969] L.W. Kennedy and O.E. Jones, “Longitudinal wave propagation in a circular bar loaded suddenly by a radially distributed end stress”, Journal of Applied Mechanics, 36: 470-478, 1969

[Kolsky 1949] H. Kolsky, “An investigation of mechanical properties of materials at very high rates of loading”, Proceedings of the Phil. Soc. Of London, B:: 62676-62700, 1949

[Krieg 1978] RD. Krieg, “A simple constitutive description for soils and crushable foams”, Report SC-DR-7260883, Sandia National Laboratory, 1978

[Li et al. 2005] Q. Li, S. Reid, H. Wen and A. Telford, “ Local impact effects of hard missiles on concrete targets”, International Journal of Impact Engineering, 32: 224-284, 2005

[Lifshitz et Leber 1994] J.M. Lifshitz and H. Leber, “Data processing in the split Hopkinson pressure bar tests”, International Journal of Impact Engineering, 15: 723-733, 1994

[Love 1927] A.E.H. Love, “A treatise on the mathematical theory of elasticity”, 4th edition, Cambridge University Press, 1927

[Love 1944] A.E.H. Love, “A treatise on the mathematical theory of elasticity”, 4th edition, Dover, New York, 1944

[Little et Childs 1967] R.W. Little and S.B. Childs, “Elastostatic boundary region problem in solid cylinders”, Quarter Applied Mathematics, 25: 261-274, 1967

[Lurie 1943] A.I. Lurie, “Theory of elasticity”, 2nd edition, Springer, 1999

[Mendelson et Roberts 1963] A. Mendelson and E. Roberts, “The axisymmetric stress distribution in in finite cylinders”, 8th Midwestern Mechanics Conference, pages 40-58, 1963

[Mindlin 1960] R.D Mindlin and H.D. McNiven, “Axially symmetric waves in elastic rods”, Journal of Applied Mechanics, 27: 145-151, 1960

[Mitra 1961] M. Von Mitra, “Disturbance produced in an elastic half-space by impulsive normal pressure”, Proc. Camb. Phil. Soc. Math. Phys. Sci., 60: 683-696, 1961

[Palaniswamy et Shah 1974] R. Palaniswamy, S.P. Shah, “Fracture and stress-strain relationship of concrete under triaxial compression”, Journal of Structural Division, ASCE, ST5: 901-916, 1974

[Rota 1997] L. Rota, “Application de méthodes inverses au dépouillement de l’essai aux barres de Hopkinson”, PhD thesis, Ecole Polytechnique, 1997

[Schmidt 2003] J.M. Schmidt, “High pressure and high strain rate behavior of cementitious materials: experiments and elastic/viscoplastic modeling”, PhD thesis, University of Florida, USA, 2003

[Sfer et al. 2002] D. Sfer, I. Carol, R. Gettu, “Study of the behavior of concrete under triaxial compression”, Journal of Engineering Mechanics, 128(2): 156-163, 2002

[Skalak 1957] R. Skalak “Longitudinal impact of a semi-infinite circular elastic bar”, Journal of Applied Mechanics, 24: 59-64, 1957

[Skoczylas et al. 2007] F. Skoczylas, N. Burlion, I. Yurtdas, “About drying effects and poro-mechanical behavior of mortars”, Concrete and Cement Composites, 29: 383-390, 2007

[Swenson et Taylor 1983] DV. Swenson and LM. Taylor, “A finite element model for the analysis of tailored pulse stimulation of boreholes”, Int. Journal of Num. Anal. Meth. Geom. 7: 469-484, 1983

[Talierco et al. 1999] A. Talierco, M. Berra, A. Pandolfi, “Effect of high-intensity sustained triaxial stresses on the mechanical properties of plain concrete”, Mag. Concrete Res., 51(6): 437-447, 1999

[Timoshenko et Goodier 1970] S.P. Timoshenko and J.N. Goodier, “Theory of elasticity”, 3rd edition, McGraw-Hill, New York, 1970

[Toutlemonde 1994] F. Toutlemonde, “Résistance au choc des structures en béton : du comportement du matériau au calcul des ouvrages”, PhD thesis, ENPC, 1994

[Vu et al. 2007] X.H. Vu, Y. Malécot, L. Daudeville, “ Comportement du béton sous fort confinement : Influence du degré de saturation et du rapport Eau/Ciment”, 25e rencomtres de l’AUGC, 23-25 Mai 2007, Bordeaux

[Vu 2007] X.H. Vu, “ Caractérisation expérimentale du béton sous fort confinement : influences du degré de saturation et du rapport eau/ciment”, PhD thesis, Université Joseph Fourier, 2007

[Warren et al. 2004] T. Warren, A. Fossum, D. Frew, “Penetration into low-strength (23 MPa) concrete: target characterization and simulations”, International Journal of Impact Engineering, 30: 477-503, 2004

[Weerheijm 1992] J. Weerheijm, “Concrete under impact tensile loading and lateral compression”, PhD thesis, Delft University, 1992

[Wei et al. 1999] X.X. Wei, K.T. Chau, R.H.C. Wong, “Analytic solution for axial point loads strength test on solid circular cylinders”, Journal of Engineering Mechanics, Vol. 125, No. 12, pages 1349-1357

[Yang et Shim 2005] L.M. Yang and V.P.W. Shim, “An analysis of stress uniformity in split Hopkinson bar test specimens”, International Journal of Impact Engineering, 31: 129-150, 2005

[Yurtdas et al. 2004] I. Yurtdas, H. Peng, N. Burlion, F. Skoczylas, “Triaxial mechanical behavior of mortar: effects of drying”, Cement and Concrete Research, 34: 1131-1143, 2004

[Zhao et Gary] H. Zhao and G. Gary, “A three-dimensional analytical solution of longitudinal wave propagation in an infinite linear viscoelastic cylindrical bar. Application to experimental techniques”, Journal of Mechanics and Physics of Solids, 43: 1335-1348, 1995

Statistiques de consultation

Repository Staff Only: edit this item